test

ROOFING FASTENERS

Washered Pins Assemblies & Accessories


P99-2613

Deck Screws™ Roofing Screws

Base Material: Steel, Wood or Concrete Roof Decks
Size Range: No. 12 x 1 5/8" to No. 12 x 8"
Screw Material: Perma-SealTM Coated Carbon Steel
Deck Screws are designed for attaching rigid insulation board, single ply membrane, and wood blocking to steel and wood decks. Some sizes can also be used in concrete decks. Available size include No. 12 in carbon steel with either hex washer or Phillips-style heads. The Deck Screws are used in conjunction with insulation or membrane plates and can also be used with batten bar. For corrosion protection the screws are coated with  Perma-Seal coating, a proprietary fluoropolymer, which meets the requirements of Factory Mutual Standard 4470.

Call for Pricing


P99-3880

Stress Plates

Bse Material: Insulation, Single-Ply Roofing Materials
Size Range: 2" and 3" Round
Screw Material: Stainless Steel, Galvalume, or Engineered Plastic Stress plates are designed for use with Deck Screws, SPIKE anchors, and Speed Lock toggles. Stress plates can be grouped into two categories; insulation plates and membrane plates. Insulation plates, as the term implies, are used when mechanically attaching rigid foam insulation to roof decks. They are manufactured in a 3" diameter for use with No. 12, No. 14, and No. 15 Deck Screws, 3/16" and 1/4" SPIKE anchors, and 1/4" Speed Lock Toggles. Two carbon steel plates, a Type 304 stainless steel plate, and a plastic plate are available. A recessed plate is available for use with the No. 12 hex washer head screws. For corrosion resistance, a Galvalume coating is applied to the carbon steel plates. Membrane plates, sometimes called lap plates, are used when mechanically attaching single ply material in the area of the lap or seam. They are manufactured in a 2" diameter for use with No. 12 Deck Screws and 1/4" SPIKE anchors, and 1/4" Speed Lock Toggles.

Call for Pricing


P99-3725

Spike®

Base Material: Concrete
Size Range: 3/16" x 1" to 1/4" x 14"
Anchor Material: Perma-SealTM Coated Carbon Steel
For roofing applications, the SPIKE is a one-piece, vibration resistant anchor available in 1/4" diameter, for use in fastening insulation, single-ply membrane, wood, and metal to structural concrete roof decks. This version of the SPIKE has a Perma-Seal coating a proprietary fluoropolymer which meets the corrosion resistance requirements of FMRC Standard 4470. It is designed for use in conjunction with Powers insulation or membrane stress plates.

Perma-Seal™ Spike®

 

Call for Pricing


P99-3790

SPIKE® Installation Tools for Roofing Applications

While the SPIKE anchor can easily be installed using a hammer, a specially designed series of drivers and manual tools provides a fast, easy to use method for installing SPIKE anchors into concrete and masonry materials. The tools allow SPIKE anchors to be installed in confined areas and prevent damage to the fixture from stray hammer blows.

Call for Pricing


P99-2896

Stainless Steel Sealing and Plastic Washers

Stainless Steel Sealing and Plastic Washers are typically used with 1/4" diameter anchors for roof flashing, termination bar and dissimilar metal applications.

Call for Pricing


P95-0012

.300 Head Drive Pins Standard Pins

Drive pins with a .300 diameter head are designed for permanently fastening a fixture to concrete, some types of masonry and A36 structural steel. Drive pins are manufactured with a 0.145" diameter shank in various lengths. Knurled shank designs are available to increase performance in steel base materials. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation.

Call for Pricing


P95-0136

.300 Head Drive Pins with Top Hat

The pins listed below are used primarily for applications fastening drywall track to concrete or steel. They are assembled with a metal top hat to provide extra bearing surface against the drywall track.

Call for Pricing


P95-0244

DX 40, DX 41, PA351™ DX 460 Pins

This 10 fastener magazine style pin will fit Hilti® DX 40 & Hilti® DX 41 tools, as well as Powers PA351™. Please note: Powers PA351™ accepts up to 1 5/8” size fasteners only.

Call for Pricing


P15-0430

8mm Head Drive Pins (X-DN Type) Pins

Drive pins with an 8mm diameter head are designed for permanently fastening a fixture to concrete, some types of masonry and A36 structural steel. Drive pins are manufactured with a 0.143" diameter shank in various lengths. Knurled shank designs are available to increase performance in steel base materials. An 8mm plastic washer is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation.

Call for Pricing


P15-0434

8mm Head Drive Pins

Call for Pricing


P95-0210

8mm Diameter Head Drive Pins with Top Hat

The pins listed below are used primarily for applications fastening drywall track to concrete or steel. They are assembled with a metal top hat to provide extra bearing surface against the drywall track.

Call for Pricing


P95-0846

10mm Head Drive Pins

Designed for permanently fastening a fixture to concrete, some types of masonry and A36 structural steel. A plastic washer is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. Use with Powers model P3600™ and P3801 tools.

Call for Pricing


P95-0220


P95-0052

Ballistic Point™ Drive Pins

Premium drive pins with a .300" diameter head have a specially designed point to allow more consistent penetration into harder base materials. Will reduce failures in dense concrete and steel. Drive Pins are manufactured with a 0.150" diameter shank in various lengths. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation.

Call for Pricing


P95-0056


P95-0322

Threaded Studs

Threaded studs are available in 1/4"-20 and 3/8"-16 thread diameters with a variety of thread and shank lengths for use in concrete, some types of masonry, and A36 structural steel. They are used for applications where it may be desirable to remove the fixture, where shimming may be required.

The shank diameter for the threaded studs is 0.143" for the 1/4"-20 diameter and 0.205" for the 3/8"-16 diameter. Knurled shank designs are available to  increase performance in steel base materials. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. On the 1/4"-20 threaded studs, a plastic cap is also provided to protect the threads of the fastener during the driving process.

Call for Pricing


P95-0097

PTZ Pins (for Pressure Treated Lumber)

PTZ Pins by DeWalt are designed for fastening through pressure treated lumber into concrete and grout filled masonry. These fasteners are manufactured to provide a minimum of corrosion resistance equivalent to triple zinc coatings (G-185) found on connector hardware available for pressure treated applications.

Call for Pricing




Results 1 - 17 of 17