ROOFING FASTENERS

Washered Pins Assemblies & Accessories


P99-2613

Deck Screws™ Roofing Screws

Base Material: Steel, Wood or Concrete Roof Decks
Size Range: No. 12 x 1 5/8" to No. 12 x 8"
Screw Material: Perma-SealTM Coated Carbon Steel
Deck Screws are designed for attaching rigid insulation board, single ply membrane, and wood blocking to steel and wood decks. Some sizes can also be used in concrete decks. Available size include No. 12 in carbon steel with either hex washer or Phillips-style heads. The Deck Screws are used in conjunction with insulation or membrane plates and can also be used with batten bar. For corrosion protection the screws are coated with  Perma-Seal coating, a proprietary fluoropolymer, which meets the requirements of Factory Mutual Standard 4470.

Call for Pricing


P99-3878

Stress Plates

Base Material: Insulation, Single-Ply Roofing Materials
Size Range: 2" and 3" Round
Stress Plates are designed for use with Deck Screws and Spike anchors. Stress plates are used when attaching insulation and single ply materials to distribute load and prevent the material being fastened from pulling over the head of the fastener. In addition to the stress plates, a sealing washer and a plastic bearing washer are available for use with flashing and termination systems.

Call for Pricing


P99-3725

Spike®

Base Material: Concrete
Size Range: 3/16" x 1" to 1/4" x 14"
Anchor Material: Perma-SealTM Coated Carbon Steel
For roofing applications, the SPIKE is a one-piece, vibration resistant anchor available in 1/4" diameter, for use in fastening insulation, single-ply membrane, wood, and metal to structural concrete roof decks. This version of the SPIKE has a Perma-Seal coating a proprietary fluoropolymer which meets the corrosion resistance requirements of FMRC Standard 4470. It is designed for use in conjunction with Powers insulation or membrane stress plates.

Perma-Seal™ Spike®

 

Call for Pricing


P95-0012

.300 Head Drive Pins

Drive pins with a .300 diameter head are designed for permanently fastening a fixture to concrete, some types of masonry and A36 structural steel. Drive pins are manufactured with a 0.145" diameter shank in various lengths. Knurled shank designs are available to increase performance in steel base materials. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation.

Call for Pricing


P95-0136

.300 Head Drive Pins with Top Hat

The pins listed below are used primarily for applications fastening drywall track to concrete or steel. They are assembled with a metal top hat to provide extra bearing surface against the drywall track.

Call for Pricing


P95-0210

8mm Diameter Head Drive Pins with Top Hat

The pins listed below are used primarily for applications fastening drywall track to concrete or steel. They are assembled with a metal top hat to provide extra bearing surface against the drywall track.

Call for Pricing


P95-0322

Threaded Studs

Threaded studs are available in 1/4"-20 and 3/8"-16 thread diameters with a variety of thread and shank lengths for use in concrete, some types of masonry, and A36 structural steel. They are used for applications where it may be desirable to remove the fixture, where shimming may be required.

The shank diameter for the threaded studs is 0.143" for the 1/4"-20 diameter and 0.205" for the 3/8"-16 diameter. Knurled shank designs are available to  increase performance in steel base materials. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. On the 1/4"-20 threaded studs, a plastic cap is also provided to protect the threads of the fastener during the driving process.

Call for Pricing




Results 1 - 7 of 7